To beat Level 367 in Parking Loop, clear the unobstructed outer perimeter vehicles first before launching cars from the inner bays. Tapping inner cars early results in invalid moves because outer bumpers physically block their exit paths. Emptying the perimeter creates the lane clearance needed to free the interior stalls while feeding vehicles onto the main loop track at steady, manageable intervals.
Layout Overview and Stall Dependencies
Level 367 divides vehicles into two distinct groups arranged around a single circular road loop:
- Outer perimeter units: Front-line vehicles positioned with direct, unblocked paths into the loop.
- Inner bay units: Vehicles positioned behind perimeter stalls that cannot move until the car ahead of them exits.
Because vehicles travel around the shared circular loop until they exit the stage, every released car becomes an active obstacle for remaining stalls. Clearing the outer perimeter unlocks physical access to trapped inner cars, but releasing exterior cars too rapidly fills the track bumper-to-bumper, leaving no merge windows for interior vehicles.
How to Clear Perimeter Vehicles and Set Loop Pace
Start the level by scanning the lot for vehicles that have direct access to the road loop without any intervening bumpers.
- Tap the first unblocked outer vehicle heading into an empty section of the road.
- Pause briefly before releasing the next perimeter car. Spacing your taps by roughly one vehicle length leaves consistent gaps in the circulating traffic.
- Clear one flank first. Opening up an entire side creates an exit corridor and gives you a clear visual lane to monitor oncoming traffic.
Rushing perimeter releases creates a dense convoy on the main road. If the loop has no gaps, newly freed interior cars have no safe moment to pull out.
Timing Inner Bay Merges
Inner bay vehicles must travel a greater distance through departure lanes before reaching the main loop. Tapping an inner vehicle the moment an opening passes the lane entrance causes a collision, because approaching loop traffic closes the distance while the inner car is still rolling toward the merge point.
To execute a clean merge, wait for a circulating car to pass the junction, then tap the inner vehicle immediately into the empty space behind its rear bumper.
| Vehicle Position | Travel Distance to Loop | Optimal Launch Window | Collision Risk |
|---|---|---|---|
| Outer Perimeter | Short | Tap into any standard open gap | Low |
| Mid-Tier Bays | Moderate | Tap as a circulating car clears the lane mouth | Moderate |
| Deep Inner Stalls | Long | Tap immediately behind the rear bumper of a passing car | High |
Vehicles in deeper stalls require earlier tap inputs to compensate for their travel latency.
Avoiding Converging Junction Collisions
Most failed attempts on Level 367 stem from side-swipe collisions at converging corners. Keep these operational rules in mind:
- Avoid consecutive releases from adjacent stalls. When two adjacent inner vehicles launch back-to-back, their paths converge at the same junction point, causing a crash.
- Alternate between opposite sides of the lot. Releasing a car from the left side and then the right side staggers vehicle entries across different sectors of the loop.
- Take advantage of no time limit. Level 367 has no stage timer. If an opening looks too narrow, let a circulating car pass and take the trailing gap behind it.
Step-by-Step Level 367 Solution Sequence
Follow this five-phase sequence to clear the stage cleanly:
- Clear the primary outer flank: Launch the unblocked exterior cars along one side of the lot, pausing between taps to establish steady spacing on the road.
- Open the secondary perimeter: Release the remaining unblocked outer vehicles on the opposite side to unlock all interior bay exits.
- Launch the first deep inner vehicle: Watch the loop, let an active car pass the newly cleared exit corridor, and tap the inner vehicle to slip into the trailing pocket.
- Alternate inner bay releases: Cycle between opposite sides of the parking grid to keep merge points spaced apart and prevent junction congestion.
- Sweep remaining vehicles: Once the majority of stalls are empty, release the final cars into the wide gaps remaining on the loop to finish the puzzle.
Free Parking Loop Codes
Current active codes and how to redeem them.
COMMUNITY
Player Comments
87 players commented on this guide.
Can you add more details about strategy in a future update?
The explanation is clear, especially for beginners.
I wish I had read this before upgrading the wrong thing.
This saved me time in the early game.