Rotate Rings Levels 131–140 Walkthrough and Solutions

To clear Rotate Rings levels 131 through 140, sequence your moves from the innermost ring outward and use middle ring cutouts as temporary holding buffers. Stages in this bracket feature compound interlocks, narrow tolerances, and multi-notch paths that prevent you from opening a direct path in a single rotation. Park internal payloads into intermediate notches before rotating exterior rings to match the final exit gate.

Mechanics Overview for Levels 131–140

Levels 131 through 140 shift away from straightforward single-ring alignment. Rings frequently share pivot points, compound seams, or tight collision boundaries where an unaligned notch halts adjacent rings.

---

Solutions for Levels 131 to 135

Level 131

1. Rotate the middle ring until its secondary cutout aligns with the exit trajectory in the bottom-right quadrant.
2. Spin the innermost core ring 180 degrees clockwise to drop the trapped piece into the middle channel.
3. Turn the outer ring until its gap aligns with the middle channel to release the piece.

Level 132

1. Leave the outer ring at its neutral starting point.
2. Spin the center ring counterclockwise until its slot reaches the nine o'clock position.
3. Turn the middle ring clockwise to complete the horizontal escape corridor toward the outer boundary.

Level 133

1. Rotate the outermost ring downward until its widest opening settles at six o'clock.
2. Move the middle ring 90 degrees counterclockwise to clear the physical obstruction caused by its thickest edge.
3. Turn the inner ring until the payload rolls out through the aligned bottom path.

Level 134

1. Focus on the left ring of the side-by-side pair first.
2. Align the cut edge of the left ring with the center intersection seam.
3. Rotate the right ring 180 degrees to receive and pull the piece across the boundary into the right perimeter.

Level 135

1. Work strictly from the innermost layer outward across the four concentric rings.
2. Align layer four (the center) with layer three.
3. Rotate layers three and four together toward the opening of layer two.
4. Turn layer one only after layers two through four form an unbroken channel.

---

Solutions for Levels 136 to 140

Level 136

1. Align the two inner rings to form a 90-degree elbow pocket rather than a straight line.
2. Rotate the payload into this temporary elbow pocket.
3. Spin the two outer rings to connect the pocket to the final exit gate.

Level 137

1. Position the innermost ring so that only one inner ball enters the middle ring at a time.
2. Rotate the middle ring to release the first ball through the outer opening.
3. Rotate the middle ring back to receive the second ball, preventing multiple loose balls from jamming the exit gap simultaneously.

Level 138

1. Ignore outer rim visual markers and track internal lip clearances instead.
2. Rotate the middle ring counterclockwise until the internal notch clicks into alignment.
3. Turn the central wheel clockwise to clear the stage.

Level 139

1. Align the intermediate ring gap directly opposite the main exit point.
2. Move the central lock piece into this neutral parking notch.
3. Rotate the outer barrier 180 degrees.
4. Move the central piece back into the transit lane and slide it out through the open exterior gate.

Level 140

1. Rotate the outer ring clockwise by one quarter turn.
2. Rotate the middle ring counterclockwise by one half turn.
3. Turn the core ring clockwise until the final path aligns and the puzzle releases.

---

Gap Sequencing and Reset Prevention

To avoid stage resets on these intermediate levels, use the following operational habits:

• Park before opening: Move internal items into a designated middle holding notch first. Once the payload is safely seated inside the intermediate layer, turn the outer rings freely without displacing the core piece.
• Clear boundary seams: Never rotate an adjacent ring while a sliding piece rests halfway across two layers. Ensure the piece has fully settled inside a channel before spinning the next ring.
• Isolate pairs: When solving four-ring layouts, solve the connection between rings one and two first, then treat that aligned pair as a single unit when bridging into ring three.